Vapour Art

GP Spheroid version 2

91,50 €
Model: GP Spheroid version 2

GP® SPHEROID V2

Generally, mesh type atomizers give better flavour than wick type atomizers. Our challenge was to make a wick type atomizer equal or even better in flavour performance with a genesis atomizer, without losing the throat hit which is usually better in wick atomizers.

The direction of the airflow, the diameter and the position of the airflow, the small fire, the quantity of the inhaling vapour, etc were the parameters that occupied us in achieving a wick type atomizer using solely resistance wire, without ceramic, adequate capacity, rich taste and vapour production with strong throat hit and simple setup.

Its feeding system works so well, that you cannot take burned taste, even with 0,9 Ohm Resistance. Its suction system gives a signal of weak taste for 10 inhales, before it runs out completely of liquid.

Filler is a sterilized water filter they use in aquariums, a good one is the SERA filter wool which one can find in pet shops and here.
 For example, all the cartomizers like the 510D Boge use similar material inside the tube where the resistance wire is, but GP® Spheroid has the filler away from the hot wire, there is no contact with it.

The vapour production and the throat hit depends on how low or high you have placed the resistance wire in relation with the air hole. Low position gives more vapour and strong throat hit. High position gives less vapour and extreme throat hit. Actually all the people who own this atomizer, have lowered the level of the nicotine they used to vap due to its strong throat hit!  

GP<sup>®</sup> Spheroid v2.1

FLAVOUR DELIVERY: ABOVE MOST WICK ATOMIZERS! 

THROAT HIT: YOU NEED TO CUT BY HALF YOUR NICOTINE LEVEL ...

EASY OF USE: FAST SETUP WITH YOUR HANDS AND FULLY REPAIRABLE EVEN THE 510 CONNECTION, THE EASIEST ATOMIZER TO SET IT UP EVEN FOR A BEGINNER TO REBUILDABLE ATOMIZERS!

SAFETY: 316 SS CONSTRUCTION, VITON O-RINGS 11X1, PEEK INSULATORS FDA APPROVED, NO WIRES, A FULL MECHANICAL ATOMIZER!

FEEDING SYSTEM: ABSOLUTE SUCTION, CONTINUOUS FLOW, PERFECT WICKING!

DRIPPING MODE: FROM ABOVE, WITH OR WITHOUT THE DRIP TIP, YOU CAN TASTE 2 DIFFERENT FLAVOURS AT ONCE!

CAPACITY: 2,2 - 3,2 ml

LEAKING: NO WAY, NO MATTER IN WHATEVER POSITION  THE ATOMIZER IS PUT! POCKET FRIENDLY, SAFE USE DURING FLYING (pressure changes doesn't affect the atomizer's tank)

E-LIQUID: FROM 100% PG (for people with SS throats) TO 100% VG (for the purists). 

NICOTINE DELIVERY: YOU NEED TO CUT BY HALF YOUR NICOTINE LEVEL. 

DRIP TIP: ACCEPTS ALL KINDS OF DRIP TIPS.

DIMENSIONS: 45 mm without the 510 connection.

ABOUT THE FLAVOUR DELIVERY: The airflow is responsible for the strong flavour, that was the initial project. Later on, we perfected the hemispherical bell as a concentrator for the flavour, we experimented changing the bells to find the right shape of the bowl, its depth, distance from the wick, and the correct internal diameter of the tube. 

The air hits the coil directly, then swirls in the chamber before being sucked out through the hemispherical cone, we call it bell, which creates a bit of Venturi effect. 

The matter of the intense flavour with the dark tones is the result of 4 months experimentation, we changed the bell 5 times to conclude to this one. The certain diameter of the tube and the hemispheric internal cup, we are calling it "bell", works as an alchemical athanor, which concentrates the vapour in a bowl from which delivered to the user as an compressed flavour, without any taste of unburnt e-liquid. 

The unit comes with a GP® Fork tool, 1 meter wire, 1 meter wick, 3 Viton O-rings and filler material.

The whole unit can be taken apart to be cleaned, there are no wires or welding, it is a full mechanical rebuildable atomizer. We recommend to clean the unit prior the use and to open the base by unscrewing the reverse threaded 510 bottom cap, occasionally and clean it from remnants of eliquids.

The unit comes in bead blasted, hand brushed and hand polished finish made by our skilled polishers.

 

 


GP® Spheroid Atomizer Review

 

Here is a extremely detailed photographic review for the GP® Spheroid in Russian language, by Karabas (Vladislav Krizhanovskiy) from Truevaping.ru 

 

GP® SPHEROID V2 UPDATE

Updated materials (certified European SS 316 surgical grade, PEEK thermoplastic insulator reinforced with glass fibres for stiffness and durability, FDA approved), increased machining precision (CNC 4 axis with state of the art tools like electrodynamic drilling) and new logo.

All units pass through ultrasonic bath, but we recommend to take apart the base of the unit and clean with a light sop solution before the use.

All the new revisions of GP® Spheroid will have even better machining and superb threading because of an additional process, we have incorporated into our production pipeline.

The bead blasted finish is an additional treatment after the brushed finish and gives a scratch resistant surface that doesn't slip in the hand. 

A small tool, the GP® Fork, which facilitates the opening of the base cap.

We give advance notifications via our news section of VapourArt®VaporWall, ECFUKVapersVapePitAussieVapersFacebook 

and Twitter for the upcoming batches of every product. 

The link below is about tips & tricks for GP® Series in ECF

GP® Series by VapourArt® - Advance Notifications, Tips & Tricks & Updates Thread

 

 


Out of stock!